Filter
GOINGMAKE All Metal Pocket Hole Jig Kit
Three-hole pocket jig for face frames and carcasses
GM1031E
GOINGMAKE Cabinet Door Mounting Jig
Holds cabinet doors in place while you hang them
GOINGMAKE 3-Axis Concealed Hinge Jig Ultra
Cup and screw holes drilled without bit swaps
GOINGMAKE 35 mm Replacement Hinge Bits, 2 Pack
Spare 35 mm carbide cutters for our hinge jigs
Compare
GOINGMAKE cabinet and joinery jigs side by side
Compare all 8 cabinet and joinery jigs
| Model | Cup | Hinge offset | Holes | Bushings | Clamping | Rating | From |
|---|---|---|---|---|---|---|---|
| Concealed Hinge Jig | 35 mm carbide-tipped bit, double bearings | 2, 3, 4, 5 and 6 mm | - | - | - | 4.6 (685) | $49.99 |
| All Metal Pocket Hole Jig Kit | - | - | 3 guides, 3/8 in, 3 spacings | - | - | 4.6 (243) | $52.99 |
| Cabinet Door Mounting Jig | - | - | - | - | 3/8 to 2-15/16 in thick | 4.6 (164) | $29.99 |
| Dowel Jig Kit | - | - | 3 at a time, center-line pointer | 1/4, 3/8 and 1/2 in | - | 4.4 (163) | $89.99 |
| Compact Concealed Hinge Jig | 35 mm carbide-tipped bit, double bearings | 3, 4, 5 and 6 mm | - | - | - | 4.6 (116) | $33.99 |
| 3-Axis Concealed Hinge Jig Ultra | 35 mm, 3-axis drill guide | 2, 3, 4, 5 and 6 mm | - | - | 1/2 to 1-1/4 in, extra block for thicker doors | 4.7 (89) | $75.99 |
| Door Hinge Mortise Jig | - | - | - | - | - | 3.8 (44) | $19.99 |
| 35 mm Replacement Hinge Bits, 2 Pack | - | - | - | - | - | 5.0 (1) | $29.99 |
Cabinet doors, face frames and carcass joints
A cabinet door hangs on a hinge whose 35 mm cup is bored into the back of the door. Our three hinge jigs clamp on, bore the cup square at an offset of 2 to 6 mm and pull the chips into a vacuum hose. The door mounting jig then holds the door at height on the face frame or the cabinet side while you drive the screws.
For the box itself, the pocket hole jig drills three 3/8 in holes at a time in stock from 1/2 to 1-3/4 in, and the dowel jig drills 1/4, 3/8 or 1/2 in holes on a line you mark across both parts.
Every cabinet jig on this shelf belongs to the GOINGMAKE catalog. Before you set up a cabinet jig, read Concealed cabinet hinges: boring the 35 mm cup, setting the offset, hanging the door.
Questions
Questions about GOINGMAKE cabinet and joinery jigs
Which GOINGMAKE hinge jig should you use for a whole kitchen?
The 3-axis hinge jig: it bores the 35 mm cup and has a separate fixed guide for the screw holes, so one setting carries through every door. It clamps doors from 1/2 to 1-1/4 in, more with its extra block.
Can you hang a cabinet door alone with the GOINGMAKE mounting jig?
That is its job. It clamps to framed or frameless cabinets, left or right hand, holds the door at height, and a removable edge pin positions full-overlay doors without measuring.
Do you need a router for the GOINGMAKE door hinge jig?
Yes. It is a router template for door hinge mortises from 2-1/2 to 5 in long, and the kit includes a router bit. Read boring cups and setting the offset for cabinet hinges.
Hinge cups are drilled and hinge mortises are routed: both go best with the work clamped and your eyes covered.